1·In the low temperature, corrosive medium or vacuum conditions, with special performance should be considered the gasket.
在低温，腐蚀性介质或真空条件下，应考虑具有特殊性能的密封垫。
2·Mechanical seal: seal face, gasket and shaft seal, etc parts must be undamaged, otherwise will result in over leakage, sure to change parts with wear and tear or damage.
机械密封：密封面、密封垫及轴封等元件必须完好，否则将导致过度泄漏，对有磨损或损伤的元件必须更换。
3·Regular testing of gasket resiliency and inspection at Receiving due to sensitivity to inconsistent quality.
由于质量差异导致灵敏性差异，因此需要经常进行密封垫弹性测试和检查接受性。
4·Class 150: Corrugated graphite-filled steel gasket.
150磅级：石墨填充波纹钢板密封垫。
5·Combined with copper outer tubes, carbon steel inner tubes, precision machined gasket surfaces, and fully expanded tube depth, this design assures efficient, dependable performance.
镀铜外管、碳钢内衬管、精密加工的密封垫表面以及全扩展的管深度，保证了高效和稳定的性能。
1·The urethane liner extends over the flange face to serve as the valve's flange gasket.
这种氨基甲酸乙酯延展覆盖到法兰表面，起到阀门法兰衬垫的作用。
2·The straight threads of the nut engage with the mating threads of the valve outlet and are tightened to compress the gasket between the two sealing surfaces.
螺母的直螺纹同阀门排气口的配合螺纹咬合在一起并上紧，来压缩在两个密封表面之间的衬垫。
3·It is essential to use a new gasket each time the connection is tightened because the softened nickel washer becomes hardened after each compression.
因为在每次压缩之后软化的镍垫圈会变硬，每次接头上紧时必须使用新衬垫。
4·Slower leak rates can be obtained with these connections depending on surface finishes, gasket materials, and mechanical condition.
依赖于表面光洁度、衬垫材料和机械状况，用这些接头可以获得更慢的泄露率。
5·Conductive gasket material is one of the most widely used shielding materials at present, and plays an important role on the suppression of electromagnetic slot -leakage in electronic equipment.
导电衬垫材料在抑制电子设备缝隙电磁泄漏中发挥了重要作用，是目前电子设备中应用最为广泛的一类屏蔽材料。
1·When the pipe joint screw, should follow the principle of diagonal twist, not one by one in order to operate, do not screw the screw die, so that the correct installation of rubber gasket.
在拧管道接头螺丝时，应遵循对角互拧的原则，不要逐个顺序进行操作，不要一次性将螺丝拧死，这样才能将橡胶垫片正确地安装上去。
2·Use sealed gasket in the water path. There isn't stress on all link surface.
水道的连接应衬有密封垫片。所有连接面都不应有应力。
3·If want to use metal gasket, it should be smooth surface narrowed, make its and gaskets of contact area is reduced.
如果要用金属垫片，则应将光滑面缩小，使其与垫片的接触面积减小。
4·Flange form different requirements, the use of gasket are different.
法兰形式不同，要求使用的垫片也不同。
5·Seal gaskets are closed in the support points of plates resist high press fluid impact and prevent leak out of fluids. Twice gelatinize technology make gasket firm connected.
处于板片有力支撑点包围中的密封垫片，能承受较大的流体冲击，不会泄漏，两次涂胶工艺保证了密封垫片牢固粘接。