Tolerances英文翻译_Tolerances是什么意思_(公差的英文)_月亮词典

Tolerances

界值

常用释义

词性释义

n.

界值，容差（tolerance 的复数）

v.

给……定公差（tolerance 的第三人称单数）

例句

全部

Compliance with the tolerances and the requirements for the general condition lies within the responsibility of the manufacturer.

一般条件的容差和要求的符合性在制造商的责任中列出。

Machining is capable of creating geometric configurations, tolerances, and surface finishes often unobtainable by any other technique.

机加工能够达到几何形状，公差及表面精度，这些通常其他的技术都达不到。

Optimal dimensional and geometric tolerances could be obtained by an appropriate optimization algorithm for the model.

求解该模型能同时得到优化的尺寸公差和形位公差。

"It is possible that the different cryptic species will have different tolerances to these chemicals, " says King.

“不同隐性物种对这些化学药品有不同的耐药性是可能的，”金说。

problems since tolerances decrease down to the range of the surface roughness.

问题，因为减少到公差范围内的表面粗糙度。

Specifications should be very clear for the vendor . The testing method and allowed tolerances should be indicated .

卖主对产品的规范说明必须非常清晰。测试方法和允许的误差必须显示。

However, the form tolerances must be kept within narrow limits as the accuracy of form directly affects the running accuracy of the bearing.

但是，形状公差必须保持在较小的范围内，因为形状精度直接影响轴承的运行精度。

paper - untrimmed sizes - primary range and supplementary range designation and tolerances , expression of direction of manufacture.

纸张。未切边的规格。基本范围和辅助范围的标称及公差制造方向的表示。

Semi-finished products made of magnesium alloys. U-sections. Tolerances on dimensions and recommended dimensions.

镁合金制半成品 .U 形型材 .尺寸公差和推荐尺寸

NON-ROTATING STEM Non-rotating stem has close roundness and straightness tolerances and is burnished for a superior finish.

不旋转阀杆不旋转阀杆具有精密的圆度和平直度公差，并且经过抛光达到极高的抛光度。

There may be differences between the tolerances of the different codes, and when using please refer to the original codes.

不同标准规定的极限偏差可能会略有差异，使用时请查阅原标准。

semi - finished products made of metal or non - ferrous alloys . titanium sheet , dimensions and tolerances.

金属或有色合金半成品。钛板材。尺寸和公差。

HYDRAULIC FLUID POWER. CYLINDER. DIMENSIONS AND TOLERANCES OF CAST IRON PISTON RINGS AND OF THEIR HOUSINGS.

液压传动 .千斤顶 .铸铁活塞环和活塞室公差和尺寸

RAILWAY MATERIAL IN GENERAL. TOLERANCES AND FITS USED PARTICULARLY FOR FIXED PARTS OF ARTICULATIONS. INTERFERENCE FITS.

通用铁路设备 .绞接固定器件用特殊公差与配合 .紧配合

Railway rolling stock drilled axles. Quality requirements. Tolerances. Surface conditions. Special dimensional indications.

铁路车辆 .空心车轴 .质量要求 .公差 .表面的状况 .特殊尺寸表示

These initiatives have resulted in significantly improved consistency and mould quality, reduced tolerances and an enhanced design process.

这些举措大大改进了强度和模具的质量，降低了公差，加快了设计过程。

All items supplied by CLIENT shall be assembled erected and aligned by the contractor as per the specification tolerances prescribed.

承包商负责所有业主供货范围的组装，安装和对位，并严格按照规格，公差，规定执行。

In the business card printing and membership card should always be making workshop temperature and air humidity in a smaller tolerances.

在制卡和会员卡制作车间边应本末保持温度和氛围湿度在较小的公役边。

and components can be produced with dimensions that need little or no rectification to meet the dimensional tolerances.

所以零件尺寸几乎无需校正就能满足尺寸公差。

In mass production, where mating parts must be interchangeable , unilateral tolerances are customary.

在大规模生产中，要求互相配合的零件时可互换的，因此单向公差更合适。

For a Tolerance Stackup with many dimensions and tolerances, statistical tolerance analysis may be more appropriate.

统计公差法叠加处理许多尺寸公差可得出更合适的结果。

Close register Used to describe jobs having small register tolerances. Also called Tight register .

精细套正用来描述只容许微细宽限作套印的印件。

The tolerances for the bore and outside diameters of rolling bearings are internationally standardized , see section " Tolerances " .

滚动轴承的内径与外径公差已经国际标准化，见“公差”一节。

网络释义

公差

· 公差 (Tolerances) - 这些是与公差格式相关的参数。当尺寸由数字的转向符号的时候出项这些符号。

允许偏差

尺寸、力学性能和允许偏差_海城正昌钳工_新浪博客 ... 15 力学性能 mechanical propertics 16 允许偏差 tolerances 11 数值 val…

容差

请懂机械的帮助看一下 ... +/- 1 degree +/-1 读 Tolerances 容差，公差 Decimal 十进制/ 小数 ...

公差设置

...2 分配设置(Allocations)2.1.3 公差设置(Tolerances)2.1.4 传输参数设置(Communications)2.1.5 文件参数设置(Files)2.1.6 打印 …

容差设定

上面的框是容差设定（Tolerances），包括：Fidelity（精度设置）：指Illustrator对手写笔书写轨迹的追踪精度，精度范围从0.5 …

容限

工艺技术的容限(tolerances)已经逼近设计规则边际(design rule margin)，这也影响到芯片的良率，甚至在新工艺节点第一次试 …

容许偏差

压力容器工程规定中英文对照 ... Neck Thickness 颈部厚度 Tolerances 容许偏差 C O N T E N T S 目录 ...

尺寸公差

42、尺寸公差（Tolerances）可以允许的误差范围。 43、模具型腔（Tool Cavity）指一空间，珠粒充满其中形成模型。

常用短语

Adj.+n.

great tolerance

v.+n.

n.

更新时间：2025-05-02 03:10