deflections英文翻译_deflections是什么意思_(变形量的英文)

An increase in resistance to roll deflections may be gained by splitting the single strut into a fork at the top.

Both fatigue and shock loads must be considered in obtaining the stresses and deflections of the various portions of positive clutches.

在求解刚性离合器各个部分的应力和疲劳时，疲劳和冲击载荷必须被考虑。

However, as an intellectual, Kristol's fight for freedom is idealistic, which in real politics prove to be deflections.

然而，克里斯托作为一名知识分子对自由的追求充满了理想主义色彩，因此他的许多主张在现实政治中不一定奏效。

The major application of these data is to define the control deflections required to stabilize the vehicle.

这些数据的主要应用是确定稳定飞行器所需要的控制偏角。

Based on a 3-layer BP artificial neural network and the layered elastic moduli was back calculated by the surface deflections.

基于三层 BP 神经网络和层状弹性理论，由路表变形反算土基回弹模量。

We have done some loading testing on the panel with different initial deflections and different stiffener.

对不同初始挠度以及不同加劲规格的薄板作了加载试验。

When aerodynamic solution and structural deflections are both converged, the aerodynamic characteristic of the elastic wing is obtained.

将非线性气动力与结构线化机翼弹性变形耦合迭代求解。

Vertical elements carry sufficient load through cantilever action to produce cantilever deflections equal to arch deflections.

垂直杆件则借悬臂作用产生和拱挠度相等的悬臂挠度，来承担足够的荷载。

It is a unique way of analyzing deflections and is even useful for finding the reactions of indeterminate structures.

这是一个独特的方式分析挠度，甚至为找到有用的不确定结构的反应。

To handle possible deflections, hydraulic devices below each vertical member are tuning the verticality of the grid.

为了处理可能出现的偏差，液压装置的垂直下方每个成员都调整垂直的网格。

The deflections of the vertical happen to be known in this case (see below).

垂直偏斜碰巧在此例中有证明（看下图）。

Large deflections by these control surfaces in flight would produce large but transient increases in specular backscatter.

在飞行状态下，操纵面的大幅度偏斜将会产生巨大且短暂的反向散射增量。

This renders the bearing like other self-aligning bearings, impervious to misalignments and shaft deflections.

有这种装置的轴承就像自调整轴承，可以避免误差和轴倾斜。

Make relevant calculations for torques, deflections, stresses, etc.

考虑力矩、偏角、压力等方面的相关计算。

We may use the plane stress analysis for determining deflections in the midplane of the beam.

我们可以用平面压力的分析方法来确立梁中间面的挠度。

Measuring crank deflections for per cylinder, in accordance with diesel works requirements and criterions.

主机各缸臂距差均在主机厂要求的范围内，符合规范的要求。

These deflections, which are stronger for denser bunches, accumulate turn after turn and may eventually lead to particle loss.

如果在每一圈的偏离都累积起来，很可能会导致意外的粒子损失。

The deformation of frame-tube structure under the lateral load is constituted by both shear and bend deflections.

框筒结构在水平荷载作用下的变形由剪切变形和弯曲变形两部分组成，弯曲变形必须考虑正、负剪力滞的影响。

Unexpected deflections can cause severe edge loading that is detrimental to gear surface life as well as noise performance.

意外的轴变形将造成严重的边缘载荷，将减少齿轮寿命，并产生噪音。

Upper-lower coal seam groups are focused by wrinkles and deflections rule time and funds are saved efficiency of production is raised.

利用褶曲、挠曲的分布规律预测其在上下煤组中出现的可能性，可以大大节约时间和经费，提高生产效率。

The marketing literature address that axle deflections have a significant impact on gear tooth strength.

研究文献表明，轴的变形对于螺旋锥齿轮强度有着明显的影响。

In my location, traffic on the street gives me regular deflections of 0. 5 degrees for cars and up to 2. 0 degrees for big trucks and buses.

在我所处的位置，街上的交通让我所测出的结果有所偏斜。一般车子是 0.5 度，大卡车货公车则是 2.0 度。

They've divided us right down the middle with their deflections.

许久我们有权拦腰分割与挠度。

In the Centre of the Reeler select scroll, roller weight and biosynthe pianzhuan deflections are the most important factor.

在为洋心卷纸机拔取卷轴的时间，滚筒不沉量和分解的偏转挠曲是最主给的感化身分。

For example, ball and roller bearings can be of the self-aligning type to accommodate shaft misalignment and deflections .

例如，滚球轴承和滚珠轴承属于自行调整式，能调适轴心差和轴偏转。

Inversion of Gravity Anomalies from Along-track Vertical Deflections with Satellite Altimeter Data and Its Applications

卫星测高数据的沿轨迹重力异常反演法及其应用

Reliability Analysis of the Formulae for Calculating Reinforced Concrete Flexural Members'Deflections and Maximum Crack Widths

混凝土受弯构件挠度与裂缝计算公式的可靠度分析

Testing method for deflections with a falling-weight-type impulse load device

利用自由落体物的摊铺材料挠度测试方法

Test Method for Deflections with a Falling-Weight-Type Impulse Load Device

落重型脉冲负荷装置挠曲的试验方法

The Stationary and Minimum Complementary Energy Principles of Bending of Thin Plates for Large Deflections

大挠度弯曲薄板的驻值和最小余能原理

挠度

n.

变形量

偏斜

偏折