MICROHARDNESS英文翻译_MICROHARDNESS是什么意思_(显微硬度的英文)_月亮词典

MICROHARDNESS

微硬度

常用释义

词性释义

n.

微硬度；[力] 显微硬度

例句

全部

The high frequency induction hardening can't raise the surface microhardness of the cold precision forging spur gear.

高频感应淬火不能达到硬化冷精锻直齿圆柱齿轮齿面的目的。

After ultrasonic impact, the surface microhardness and the section microhardness are obviously increased.

冲击后接头的表面和断面显微硬度均得到了提高。

The microhardness distribution of the welded joint is along the welding line. The microhardness is higher in nugget zone, and lowest in HAZ.

焊接接头的硬度分布沿焊缝中心基本对称，焊核区硬度较高，热影响区硬度最低。

The microhardness is higher and grain size is smaller in weld bead zone, compared with the heat-affected zone and base metal.

相对母材和热影响区，焊缝的晶粒明显细小，显微硬度比热影响区和母材稍高。

The microhardness of the cladding layer was measured by microhardness tester, and its microstructure was observed by SEM.

利用维氏硬度计测试了其显微硬度，用扫描电镜分析了激光熔覆层的微观形貌。

The deposition rate, microhardness, corrosion rate of low temperature iron plating layer at different temperatures are investigated.

研究了在不同温度下获得的低温镀铁层的沉积速率、显微硬度、腐蚀速率等性能。

The result showed that the microhardness, finish and time of strengthening layers related to parameter of strengthening technology.

试验结果表明，表面强化层硬度、表面光洁度和强化时间与选择工艺参数有关；

The hardening layer was analyzed by metalloscope, microhardness, electronic probe and transmission electron microscopy.

用金相显微镜、显微硬度计、电子探针和透射电镜对硬化层进行分析。

The depth and microhardness distribution of alumetizing layer obtained on different technical conditions were measured.

测定了不同工艺条件下获得的浸渗层深度和浸渗层显微硬度的分布。

The morphology, properties and microstructure of the coatings were studied by SEM, XRD, and microhardness tester.

用扫描电镜、X 射线衍射仪和显微硬度计分析了电火花表面强化层形貌、性能和组织结构。

Microhardness, depth profile and wear mechanisms were investigated by means of MVK H12, TALYSURF6, XPS and microscopy.

采用显微硬度、轮廓深度、XPS、显微镜观察等研究磨损机理。

The microhardness treated by plasma heat treatment is notably improved, and the wear resistance and operating life increase obviously.

处理后的表面硬度有显著提高，并明显提高了发动机缸体的耐磨性和使用寿命。

Microstructure and surface morphology of the oxynitriding layers were studied by SEM, XRD, microhardness tester and digital camera.

利用 SEM、XRD、显微硬度计和数码相机等研究氧氮共渗层的微观组织、结构及表面形貌。

The microhardness of the processed zone is lower than the cast metal, but further uniform microhardness is observed in the processed zone.

搅拌摩擦加工后，加工区的显微硬度较铸态区降低，但分布比较均匀；

The measured values of microhardness were calculated using mathematical statistic method.

使用数理统计的方法对显微硬度测试值进行了处理。

The copper deposit also represented higher microhardness and better corrosion resistance.

电铸铜的显微硬度和抗腐蚀性能均明显提高。

The microhardness distribution on cross section at both sides of the interface changed smoothly.

断面上微观硬度分布在界面两侧变化平缓。

The microstructure, microhardness and wear resistance of compound region were observed and measured.

对复合区进行显微组织观察及分析、显微硬度测量、耐磨性能测试。

The microhardness and surface roughness increase with the shot peening intensity increase.

硬度和粗糙度都随喷丸强度的增加而增大。

Vickers hardness testing of resistance spot, projection and seam welds (low load and microhardness).

电阻点焊、凸焊和滚焊的维氏硬度试验（低荷载和超微硬度）

The microhardness and wear resistance of the implanted layer were determined.

对注入层的显微硬度和耐磨性进行了测试。

The microhardness of twin spot laser welded joint is higher than that of single spot laser welded joint, but lower than that of base metal.

双光点激光焊接头各区域硬度低于母材，但高于单光点激光焊接头；

网络释义

显微硬度

冶金词汇英语翻译(H-N) ... micrography 显微检验 microhardness 显微硬度 microhardness tester 显微硬度计 ...

微型硬度

努普显微硬度试... ... 1) 硬度; hardness 5) 微型硬度; microhardness 6) 最小点燃电流比; minimum ignition current ratio;MICR ...

微硬度分析

2-5-1微硬度分析(microhardness) 19 2-5-2 偏光法(polarizing microscope) 19 2-5-3 X光微显影技术(x-ray microradiography) 21 …

显微维氏硬度计

渗层有硬度，须用显微维氏硬度计(microhardness)检测表面硬度。HV500左右(Layer Thickness less than 2mm)ztljlljtk 2006-10 …

压痕硬度值

...间后卸除试验力，用测量的压痕对角线长度计算的一种压痕硬度值 (microhardness) 显微硬度主要用于确定很薄的材料、细金 …

更新时间：2025-05-01 16:12